RE: [microblaze-uclinux] Questions on auto-config build flow

["David Banas" <dbanas@xxxxxxxxxxxxxx>]

Sathya,

I don't seem to have any 'intc' peripheral defined in my 'system.mhs' file.
Is it mandatory?

David Banas
Field Applications Engineer
Nu Horizons Electronics Corp.
2070 Ringwood Avenue
San Jose, CA 95131
(408)434-0800 - office
(415)846-5837 - cell
http://www.nuhorizons.com
-----Original Message-----
From: owner-microblaze-uclinux@itee.uq.edu.au
[mailto:owner-microblaze-uclinux@itee.uq.edu.au] On Behalf Of
Sathyanarayanan Thammanur
Sent: Wednesday, January 26, 2005 1:39 PM
To: microblaze-uclinux@itee.uq.edu.au
Subject: Re: [microblaze-uclinux] Questions on auto-config build flow

David,
Can you paste your intc peripheral snippet from MHS ? I suspect this 
could be coming from that peripheral.

Sathya


David Banas wrote:

>Thanks, John. With that help, I was able to make quite a bit more progress.
>I now seem to have a parameter getting picked up somewhere that's too big,
>as per:
>
>----------- Build output begins here. ----------------------
>Running generate for OS'es, Drivers and Libraries ...
>#--------------------------------------
># uClinux BSP generate...
>#--------------------------------------
>drvlist : 35697028 35654384 35663344 35663904
>periph: lmb_bram_if_cntlr
>periph: lmb_bram_if_cntlr
>periph: opb_mdm
>periph: opb_uartlite
>periph: opb_uartlite
>periph: opb_emc
>periph: opb_gpio
>ERROR:MDT - ERROR FROM TCL:- uclinux () - integer value too large to
>represent
>       while executing
>   "format "0x%08X" $param_value"
>       (procedure "xprint_params" line 25)
>----------- Build output ends here. ----------------------
>
>Here's the 'opb_gpio' section from my 'system.mhs' file:
>
>---------------- system.mhs file excerpt begins here. -----
>BEGIN opb_gpio
> PARAMETER INSTANCE = opb_gpio_0
> PARAMETER HW_VER = 3.01.a
># PARAMETER C_BASEADDR = 0xFFFF_7000
># PARAMETER C_HIGHADDR = 0xFFFF_71FF
> PARAMETER C_BASEADDR = 0xFFFF7000
> PARAMETER C_HIGHADDR = 0xFFFF71FF
> PARAMETER C_GPIO_WIDTH = 32
> PARAMETER C_IS_BIDIR = 1
> BUS_INTERFACE SOPB = opb_v20_0
> PORT GPIO_IO = led
> PORT OPB_Clk = sys_clk
>END
>---------------- system.mhs file excerpt ends here. -----
>
>As you can see, I had to correct a couple of hex values that had been
>entered strangely (not sure why; I didn't create this file.), in order to
>get this far. I don't see anything in this section that looks like it's
>larger than 32 bits, do you? Any thoughts?
>
>Thanks again for all the help,
>
>David Banas
>Field Applications Engineer
>Nu Horizons Electronics Corp.
>2070 Ringwood Avenue
>San Jose, CA 95131
>(408)434-0800 - office
>(415)846-5837 - cell
>http://www.nuhorizons.com
>
>
>
>___________________________
>microblaze-uclinux mailing list
>microblaze-uclinux@itee.uq.edu.au
>Project Home Page : http://www.itee.uq.edu.au/~jwilliams/mblaze-uclinux
>Mailing List Archive :
http://www.itee.uq.edu.au/~listarch/microblaze-uclinux/
>
>  
>
___________________________
microblaze-uclinux mailing list
microblaze-uclinux@itee.uq.edu.au
Project Home Page : http://www.itee.uq.edu.au/~jwilliams/mblaze-uclinux
Mailing List Archive :
http://www.itee.uq.edu.au/~listarch/microblaze-uclinux/


________________________________________________________________________
This email has been scanned for all viruses by the MessageLabs Email
Security System. For more information on a proactive email security
service working around the clock, around the globe, visit
http://www.messagelabs.com
________________________________________________________________________


___________________________
microblaze-uclinux mailing list
microblaze-uclinux@itee.uq.edu.au
Project Home Page : http://www.itee.uq.edu.au/~jwilliams/mblaze-uclinux
Mailing List Archive : http://www.itee.uq.edu.au/~listarch/microblaze-uclinux/