Re: [microblaze-uclinux] login issue when booting

[mcnernbm@xxxxxxxxxxxxxxxxx]

John,
Suprisingly I did not do a whole lot.
 I run an update on my kernel and dist directories.  I then made
sure my auto-make file was up to date in the kernel architecture microblaze
directory.  Once I had this  I built the kernel with as little
as possible.  I took out the ethernet, flash, and gpio drivers.  I
also changed the mdm from the flash driver to the generic uclinx rom driver.
 then I ran the make dep and make and then booted thejimage.bin file
through xmd.  My commands I used where dow -data images/image 0x80000000
and then con 0x80000000.  Simple as that.  But I am still having
the issue that is will nto let me login now.  So if it keeps doing
this I may still go back and try an older kernel download.  Also what
board are you using?
Brett

John McGrath <john.mcgrath@xilinx.com>
Sent by: owner-microblaze-uclinux@itee.uq.edu.au

04/21/2005 04:31 PM

Please respond to
microblaze-uclinux@itee.uq.edu.au

To	microblaze-uclinux@itee.uq.edu.au
cc
Subject	Re: [microblaze-uclinux] login issue when booting

Hi 
It seems like you got past the previous problem you were having, detailed
in the "booting uclinux" thread. How did you do this? I am still
"hanging" at the line

uclinux[mtd]: root filesystem index=0 
VFS: Mounted root (romfs filesystem) readonly. 
Freeing init memory: 32K


Can you help?

Cheers
John

mcnernbm@notes.udayton.edu
wrote: 

When booting the uclinux on a memec v2p board I get the results below.
 But once it hits the login part I can not login.  I have tried
root as the username and pass and jsut root as used and no pass and I can
nto get it to login.  Also there is the one fail listed and not sure
if that is causing me a problem or not.  Also the only thing I changed
when I built the kerneal is I disable the ethernet and networking stuff
and the gpio driver and I also changed the MDM to the generic rom selection.
 All other option I left alone. 

zone(0): 8192 pages.ash device at locati 
zone(1): 0 pages.rch for id:(00 00 
zone(2): 0 pages.pe(2)rning: dev ( 
CPU: MICROBLAZErch for id:(00 
Kernel command line:e 
MBVanil 
CFI: Found 
Console: xmbserial on UARTLitero00 00) interleave(2) type(1)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX 
Linux NET4.0 for Linux 2.4 
Based upon Swansea University Computer Society NET3.039
Microblaze UARTlite serial driver version 1.00 
ttyS0 at 0xffff2000 (irq = 1) is a Microblaze UARTlite
Starting kswapd 
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
uclinux[mtd]: RAM probe address=0x800c58fc size=0xb2000
uclinux[mtd]: root filesystem index=0 
VFS: Mounted root (romfs filesystem) readonly. 
Freeing init memory: 32K 
Mounting proc: 
Mounting var: 
Populating /var: 
Running local start scripts. 
Mounting /etc/config: 
Populating /etc/config: 
flatfsd: Nonexistent or bad flatfs (-43), creating new one...
flatfsd: Failed to write flatfs (-43): No such device
flatfsd: Created 3 configuration files (142 bytes)
Setting hostname: 

uclinux-auto login: 

THanks for the help 
Brett