I have finally gotten uclinux running
at 100mhz on the ml403. I still can not get it to run at the 66 mhz
level. I might try a make clean and rebuilding the kernel to see
if that helps cause seems to have worked with the 100mhz but that was the
first kernel I built for the 100mhz version. So I can not be sure
that fixed some of my problems. I will try the 66mhz kernel build
again tonight and let you know of my success or failure.
Also I am currently booting using the
generic romfs what do I need to do to get the kernel to boot from on board
flash and system ace? Also what features should be enabled when building
the kernel to make sure the ethernet, usb, flash devices, and everything
else on the board is functional? It seems the ehternet is working
since it came back with a dhcp could not be found since i have not had
a chance to hook it into a network yet.
Brett
"Errol Terblanche"
<rince@necsa.co.za> Sent by: owner-microblaze-uclinux@itee.uq.edu.au
06/29/2005 06:38 AM
Please respond to
microblaze-uclinux@itee.uq.edu.au
To
<microblaze-uclinux@itee.uq.edu.au>
cc
Subject
RE: [microblaze-uclinux]
ml403
Have you been able to get a trace to see where it
dies?
I have had this problem twice now, where it dies after find_bootmap_pfn
for
no apparent reason, and without printing anything.
A "make clean" followed by "make menuconfig;make dep;make"
fixed it both
times...
Long shot but you don't have anything to loose...
I seemed to happen after I made major address changes in my hardware.
Thank you,
Errol
________________________________________
From: owner-microblaze-uclinux@itee.uq.edu.au
[mailto:owner-microblaze-uclinux@itee.uq.edu.au] On Behalf Of
mcnernbm@notes.udayton.edu
Sent: Tuesday, June 28, 2005 3:26 PM
To: microblaze-uclinux@itee.uq.edu.au
Subject: Re: [microblaze-uclinux] ml403
John here are the mhs and mss files. AS before the hardware seem
to build
fine but nit sure its 100% correct. If it is ok then I am must not
be
selecting the right options when building the kernel or something
Brett
John Williams <jwilliams@itee.uq.edu.au>
Sent by: owner-microblaze-uclinux@itee.uq.edu.au
06/27/2005 10:33 PM
Please respond to
microblaze-uclinux@itee.uq.edu.au
To
microblaze-uclinux@itee.uq.edu.au
cc
Subject
Re: [microblaze-uclinux] ml403
Brett,
mcnernbm@notes.udayton.edu wrote:
> I Have gotten the hardware to work but I can not get anything work
with
> uclinux. I built a kernel and everything and then when I go
to run it I
> get nothing out. Attached is the hardware I am using any help
in
> verifying the hardware is setup correctly would be greatly appreciated.
Can you please repost just your MHS, MSS and auto-config.in files? Much
easier for a quick examination than downloading and unpacking a 3Mbyte
archive
Regards,
John
___________________________
microblaze-uclinux mailing list
microblaze-uclinux@itee.uq.edu.au
Project Home Page : http://www.itee.uq.edu.au/~jwilliams/mblaze-uclinux
Mailing List Archive :
http://www.itee.uq.edu.au/~listarch/microblaze-uclinux/
___________________________
microblaze-uclinux mailing list
microblaze-uclinux@itee.uq.edu.au
Project Home Page : http://www.itee.uq.edu.au/~jwilliams/mblaze-uclinux
Mailing List Archive : http://www.itee.uq.edu.au/~listarch/microblaze-uclinux/