[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [microblaze-uclinux] XMD Crashing using NuHo reference design

To: <microblaze-uclinux@xxxxxxxxxxxxxx>
Subject: Re: [microblaze-uclinux] XMD Crashing using NuHo reference design
From: "Jim Law" <jlaw@xxxxxxxxxxxxx>
Date: Mon, 18 Jul 2005 08:49:20 -0400
References: <87A3F346828DFD4BB7560634C134D00B62D9C3@XSJ-EXCHVS1.xlnx.xilinx.com>
Reply-to: microblaze-uclinux@xxxxxxxxxxxxxx
Sender: owner-microblaze-uclinux@xxxxxxxxxxxxxx

Here is the XMD output:
--------------------------------------------
Xilinx Microprocessor Debug (XMD) Engine
Xilinx EDK 7.1 Build EDK_H.10.4
Copyright (c) 1995-2005 Xilinx, Inc.  All rights reserved.

XMD%
Loading XMP File..
WARNING:Portability:111 - Message file "EDK.msg" wasn't found.
Processor(s) in System ::

Microblaze(1) : microblaze_0
Address Map for Processor microblaze_0
  (0x00000000-0x00003fff) dlmb_cntlr    dlmb
  (0x00000000-0x00003fff) ilmb_cntlr    ilmb
  (0xc0000000-0xc0003fff) ethernet      mb_opb
  (0xfe000000-0xfeffffff) opb_sdram_0   mb_opb
  (0xff800000-0xffbfffff) sram_flash    mb_opb
  (0xffff1000-0xffff10ff) system_timer  mb_opb
  (0xffff2000-0xffff20ff) console_uart  mb_opb
  (0xffff3000-0xffff30ff) system_intc   mb_opb
  (0xffff5000-0xffff51ff) system_gpio   mb_opb
  (0xffffc000-0xffffc0ff) debug_module  mb_opb

Executing Connect Cmd: connect mb mdm -cable type xilinx_parallel port 
LPT1 -debugdevice cpunr 1 -pfsl port 0 type s
Closing JTAG Socket connection

Unable to Open Socket connection to Modelsim at Address: (null), Port: 
44428224

Loading MHS File..
Processor(s) in System ::

Microblaze(1) : microblaze_0
Address Map for Processor microblaze_0
  (0x00000000-0x00003fff) dlmb_cntlr    dlmb
  (0x00000000-0x00003fff) ilmb_cntlr    ilmb
  (0xc0000000-0xc0003fff) ethernet      mb_opb
  (0xfe000000-0xfeffffff) opb_sdram_0   mb_opb
  (0xff800000-0xffbfffff) sram_flash    mb_opb
  (0xffff1000-0xffff10ff) system_timer  mb_opb
  (0xffff2000-0xffff20ff) console_uart  mb_opb
  (0xffff3000-0xffff30ff) system_intc   mb_opb
  (0xffff5000-0xffff51ff) system_gpio   mb_opb
  (0xffffc000-0xffffc0ff) debug_module  mb_opb

Microblaze(1) : microblaze_0
Address Map for Processor microblaze_0
  (0x00000000-0x00003fff) dlmb_cntlr    dlmb
  (0x00000000-0x00003fff) ilmb_cntlr    ilmb
  (0xc0000000-0xc0003fff) ethernet      mb_opb
  (0xfe000000-0xfeffffff) opb_sdram_0   mb_opb
  (0xff800000-0xffbfffff) sram_flash    mb_opb
  (0xffff1000-0xffff10ff) system_timer  mb_opb
  (0xffff2000-0xffff20ff) console_uart  mb_opb
  (0xffff3000-0xffff30ff) system_intc   mb_opb
  (0xffff5000-0xffff51ff) system_gpio   mb_opb
  (0xffffc000-0xffffc0ff) debug_module  mb_opb
------------------------------------------------------------

----- Original Message ----- 
From: "Raj Nagarajan" <raj.nagarajan@xilinx.com>
To: <microblaze-uclinux@itee.uq.edu.au>
Sent: Thursday, July 14, 2005 2:20 PM
Subject: RE: [microblaze-uclinux] XMD Crashing using NuHo reference design


> Hi Jim,
>
> Can you post the XMD output..
>
> -- Raj
>
>
>> -----Original Message-----
>> From: owner-microblaze-uclinux@itee.uq.edu.au
>> [mailto:owner-microblaze-uclinux@itee.uq.edu.au] On Behalf Of Jim Law
>> Sent: Thursday, July 14, 2005 10:02 AM
>> To: microblaze-uclinux@itee.uq.edu.au
>> Subject: [microblaze-uclinux] XMD Crashing using NuHo reference design
>>
>> Hi all,
>>
>> Have:
>>
>> NuHo S3-2000 board
>> Parallel-IV cable
>> ISE 7.1.03i installed in c:\xilinx7\
>> EDK 7.1.02i installed in c:\edk7\
>> ChipScope Pro 7.1.03i
>> uClinux BSP V1.00a 16mar2005 - unzipped into
>> c:\edk_user_repository\ Dave Banas'
>> NuHo_S3-2000_uClinux_Rel2005062301.zip  - unzipped to e:\uClinux_try\
>>
>> Followed the Quick Start instructions from Dave Banas:
>> - copied the VHD files as described (noted that there is a
>> newer emc_common_v2_00_b\hdl\vhdl core in the directory -
>> ignored this)
>> - launched XPS, opened the system.xmp, "download the
>> bitstream" built and downloaded fine
>> - can see and talk to the bootloader from HyperTerm fine
>>
>> Problem:
>> - when I launch XMD, it crashes
>> - I note that the connect command has some extra switches
>> after the "cpunr 1"  switch.  The full line is:
>>  "connect mb mdm -cable type xilinx_parallel port LPT1
>> -debugdevice cpunr
>> 1 -pfs1 port 0 type s"
>> - after "Loading MHS File", it shows me the Adress Map twice,
>> and then gives a Windows report.
>>
>> Tried changing the XMD options to Sim - runs ok (but not what
>> I need <g>) Changed the settings back - same results.
>>
>> Thots? anyone?
>>
>> Jim Law
>> Iris Power Engineering
>>
>> ___________________________
>> microblaze-uclinux mailing list
>> microblaze-uclinux@itee.uq.edu.au
>> Project Home Page :
>> http://www.itee.uq.edu.au/~jwilliams/mblaze-uclinux
>> Mailing List Archive :
>> http://www.itee.uq.edu.au/~listarch/microblaze-uclinux/
>>
>>
>>
>
>
> ___________________________
> microblaze-uclinux mailing list
> microblaze-uclinux@itee.uq.edu.au
> Project Home Page : http://www.itee.uq.edu.au/~jwilliams/mblaze-uclinux
> Mailing List Archive : 
> http://www.itee.uq.edu.au/~listarch/microblaze-uclinux/
>
> 

___________________________
microblaze-uclinux mailing list
microblaze-uclinux@itee.uq.edu.au
Project Home Page : http://www.itee.uq.edu.au/~jwilliams/mblaze-uclinux
Mailing List Archive : http://www.itee.uq.edu.au/~listarch/microblaze-uclinux/

Follow-Ups:
- RE: [microblaze-uclinux] XMD Crashing using NuHo reference design
  - From: David Banas

References:
- RE: [microblaze-uclinux] XMD Crashing using NuHo reference design
  - From: Raj Nagarajan

Prev by Date: Re: [microblaze-uclinux] uClinux bootup problems
Next by Date: [microblaze-uclinux] Kernel Compilation Error
Previous by thread: RE: [microblaze-uclinux] XMD Crashing using NuHo reference design
Next by thread: RE: [microblaze-uclinux] XMD Crashing using NuHo reference design
Index(es):
- Date
- Thread