[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [microblaze-uclinux] No luck
Folks,
When I attempt to connect via XMD I see the following output:
WARNING: English is not supported as a language. Using usenglish.
Xilinx Microprocessor Debug (XMD) Engine
Xilinx EDK 7.1.1 Build EDK_H.11.3
Copyright (c) 1995-2005 Xilinx, Inc. All rights reserved.
XMD%
Loading XMP File..
WARNING:Portability:111 - Message file "EDK.msg" wasn't found.
Processor(s) in System ::
Microblaze(1) : microblaze_0
Address Map for Processor microblaze_0
(0x00000000-0x00001fff) dlmb_cntlr dlmb
(0x00000000-0x00001fff) ilmb_cntlr ilmb
(0x22000000-0x227fffff) FLASH_2Mx32 mb_opb
(0x24000000-0x27ffffff) DDR_SDRAM_64Mx32 mb_opb
(0x40600000-0x4060ffff) RS232_Uart mb_opb
(0x41200000-0x4120ffff) opb_intc_0 mb_opb
(0x41400000-0x4140ffff) debug_module mb_opb
(0x41c00000-0x41c0ffff) opb_timer_1 mb_opb
Executing Connect Cmd: connect mb mdm -cable type xilinx_platformusb port
USB2
frequency 6000000 -debugdevice cpunr 1
Connecting to cable (Usb Port - USB22).
Checking cable driver.
Driver xusbdfwu.sys version: 1018 (1018).
Driver windrvr6.sys version = 6.2.2.2.Calling setinterface num=0,
alternate=0.
DeviceAttach: received and accepted attach for:
vendor id 0x3fd, product id 0x8, device handle 0x28b0038
Max current requested during enumeration is 280 mA.
Cable Type = 3, Revision = 0.
Setting cable speed to 6 MHz.
Cable connection established.
Firmware version = 1018.
CPLD file version = 0006h.
CPLD version = 0006h.
JTAG chain configuration
--------------------------------------------------
Device ID Code IR Length Part Name
1 0a001093 8 System_ACE
2 05059093 16 XCF32P
3 0167c093 10 XC4VLX25
4 09608093 8 xc95144xl
Assuming, Device No: 3 contains the MicroBlaze system
WARNING:EDK - MDM Peripheral Not Detected on Hardware
WARNING:EDK - Assuming opb_jtag_uart peripheral
Connected to the JTAG MicroProcessor Debug Module (MDM)
No of processors = 1
UNKNOWN Processor Version (0)
Verify if FPGA Bitstream was downloaded and DONE pin went High
XMD%
Any suggestions on how i should change the "connect mb mdm -cable type
xilinx_platformusb port USB2 frequency 6000000 -debugdevice cpunr 1" line so
that I successfully connect?
Thanks,
Andy
_________________________________________________________________
Express yourself instantly with MSN Messenger! Download today - it's FREE!
http://messenger.msn.click-url.com/go/onm00200471ave/direct/01/
___________________________
microblaze-uclinux mailing list
microblaze-uclinux@xxxxxxxxxxxxxx
Project Home Page : http://www.itee.uq.edu.au/~jwilliams/mblaze-uclinux
Mailing List Archive : http://www.itee.uq.edu.au/~listarch/microblaze-uclinux/