Re: [microblaze-uclinux] Errors with autoconfig.in file

[Vijai.S.Kumar@xxxxxxxxxxxxxxxx]

hi
although i m not sure....
but u cab try by running command
$ dos2unix autoconfig.in
them make the image.
becoz autoconfig.in is copied from windows to linux.
anyway try it.

Vijai Kumar
Reliance Infocomm,
Gurgaon, India.
ph - 09871136895




                                                                                                                                            
                      "Kunal Kishore"                                                                                                       
                      <kunalpatna@xxxxxxxxx>              To:       microblaze-uclinux@xxxxxxxxxxxxxx                                       
                      Sent by:                            cc:       (bcc: Vijai S Kumar/Services/INFOCOMM/RIL)                              
                      owner-microblaze-uclinux@ite        Subject:  [microblaze-uclinux] Errors with autoconfig.in file                     
                      e.uq.edu.au                   Importance: Normal  Sender's OU: Reliance |------------------|                          
                                                                                              | [ ] Confidential |                          
                                                                                              |------------------|                          
                      05/18/2006 10:07 AM                                                                                                   
                      Please respond to                                                                                                     
                      microblaze-uclinux                                                                                                    
                                                                                                                                            




Hi John,
I am using xilinx EDK 7.1 sp2 on WINDOWS XP to port uclinux on
microblaze.Target device is spartan 3 (xc3s200 ft256 -4) using the starter
board form Digilent. Board has one flash memory of 1 MB (platform flash
from xilinx) and SRAM 256Kx32.The "auto-config.in" thus generated is copied
to the location "linux-2.4.x/arch/microblaze/platform/uclinux-auto".After
"make menuconfig"  I get this :

--------------------------------------------------------------------------------------------------------------------

config/mkconfig > config.in
make -C /home/kunal/uc-test/uClinux-dist/config/scripts/lxdialog all
make[1]: Entering directory
`/home/kunal/uc-test/uClinux-dist/config/scripts/lxdialog'
make[1]: Leaving directory
`/home/kunal/uc-test/uClinux-dist/config/scripts/lxdialog'
Using defaults found in .config
Preparing scripts: functions, parsing...done.

Saving your kernel configuration...

*** End of Linux kernel configuration.
*** Check the top-level Makefile for additional configuration.
*** Next, you must run 'make dep'.

make[1]: Entering directory `/home/kunal/uc-test/uClinux-dist'
make ARCH=microblaze CROSS_COMPILE=mb- -C linux-2.4.x oldconfig
make[2]: Entering directory `/home/kunal/uc-test/uClinux-2.4.x'
rm -f include/asm
( cd include ; ln -sf asm-microblaze asm)
/bin/sh scripts/Configure -d arch/microblaze/config.in
#
# Using defaults found in .config
#
*
* Code maturity level options
*
Prompt for development and/or incomplete code/drivers (CONFIG_EXPERIMENTAL)
[Y/n/?]
*
* Loadable module support
*
Enable loadable module support (CONFIG_MODULES) [Y/n/?]
  Set version information on all module symbols (CONFIG_MODVERSIONS)
[N/y/?]
  Kernel module loader (CONFIG_KMOD) [N/y/?]
*
* Processor type and features
*
*
* Platform
*
Platform (uclinux-auto, ML401, MBVanilla, Egretv0.1, SUZAKU) [uclinux-auto]
  defined CONFIG_UCLINUX_AUTO
Memory model (RAM, ROM) [RAM] (NEW) ram
  defined CONFIG_MODEL_RAM
: command not foundtform/uclinux-auto/auto-config.in: line 8:
: command not foundtform/uclinux-auto/auto-config.in: line 9:
: command not foundtform/uclinux-auto/auto-config.in: line 10:
: command not foundtform/uclinux-auto/auto-config.in: line 14:
: command not foundtform/uclinux-auto/auto-config.in: line 18:
: command not foundtform/uclinux-auto/auto-config.in: line 21:
: command not foundtform/uclinux-auto/auto-config.in: line 66:
: command not foundtform/uclinux-auto/auto-config.in: line 76:
: command not foundtform/uclinux-auto/auto-config.in: line 86:
: command not foundtform/uclinux-auto/auto-config.in: line 100:
: command not foundtform/uclinux-auto/auto-config.in: line 114:
: command not foundtform/uclinux-auto/auto-config.in: line 136:
: command not foundtform/uclinux-auto/auto-config.in: line 158:
: command not foundtform/uclinux-auto/auto-config.in: line 223:
: command not foundtform/uclinux-auto/auto-config.in: line 230:
GPIO driver (CONFIG_XILINX_GPIO) [Y/m/n/?]
Ethernet driver (CONFIG_XILINX_ENET) [Y/m/n/?]
SystemAce driver (CONFIG_XILINX_SYSACE) [N/y/m/?
---------------------------------------------------------------------------------------------------------------------

And susequently I get a long list of  parse errors after "make" in
/home/kunal/uc-test/uClinux-2.4.x/include/linux/autoconf.h file.
**  Image files are built successfully  when  "auto-config.in"  file used
is  the  originally  downloaded one  from  cvs  repository.
Is there a problem with my board.Is this board not supported ?

Kindly suggest a solution as soon as possible.
Thanks in advance.

Regards,

Kunal Kishore


___________________________
microblaze-uclinux mailing list
microblaze-uclinux@xxxxxxxxxxxxxx
Project Home Page : http://www.itee.uq.edu.au/~jwilliams/mblaze-uclinux
Mailing List Archive : http://www.itee.uq.edu.au/~listarch/microblaze-uclinux/