Could you let me know what configuration did you change to get this fixed? I have the same problem and am still struggling with it.
----- Original Message ----
From: Torrego Raul <RTorrego@xxxxxxxxxx>
To: microblaze-uclinux@xxxxxxxxxxxxxx
Sent: Monday, January 21, 2008 2:46:53 AM
Subject: RE: [microblaze-uclinux] problems with download image.bin for kernel 2.6
Hi Michal,
Thanks for your help, I had the same problem and I have finally been
able to fix it.
You were right, and the problem was not that "nothing happened" but,
what happened was not displayed. It seems that in the 2.6 kernel the
defaul option is not to output the console through the UART. I have changed
some configuration about this (I exactly don´t know where, I must
look for it now ;-) ) and now it works fine.
Thanks again.
Raúl
________________________________
De:
owner-microblaze-uclinux@xxxxxxxxxxxxxx en nombre de Michal Simek
Enviado el: dom 20/01/2008 15:06
Para:
microblaze-uclinux@xxxxxxxxxxxxxxAsunto: Re: [microblaze-uclinux] problems with download image.bin for
kernel 2.6
Hi,
> i give up with 2.6 kernel and i am working with 2.4 kernel, until
now,
> no one can response me why is this problem and how can i fix it, so
i
> quit.
1. Kernel 2.6 is good choice.
> i am sure that is the kernel setting configuration, because in 2.4
and
> 2.6 menus of "make menuconfig" are different. And some options change
> since 2.4
2. Yes, .config files from 2.4 and 2.6 are different
> but appers next message in terminal window:
>
> found romfs @ 0x4416108c (0x000ee000)
> #### klimit 44175000 #####
> Moving 0x000ee000 bytes from 0x4416108c to 0x44174d54
> New klimit: 0x44263000
>
> and then nothing else happens. What is it happen??, i am using
> Spartan 3E rev. D, my test Memory works fine, and i change my
mode
> jumpers to M.S. mode and to FPGA mode.
3. nothing happens? I think that a lot of things happen but you don't
have output on console. Be sure that you have correct setting for your
serial driver. I hope you use uartlite.
> and then nothing else happens. What is it happen??, i am using
> Spartan 3E rev. D, my test Memory works fine, and i change my
mode
> jumpers to M.S. mode and to FPGA mode.
4. test Memory only tells you that the memory seem works properly -
this
test is very simple and covers only small amount of faults.
5. Do you use U-BOOT? U-BOOT helps you testing your design more
carefully and helps you with booting kernel.
If you use U-BOOT I recommend you check the log_buf of kernel
# cat System.map | grep __log_buf (output is memory address)
output is 441bf650
in U-BOOT you can see output like this.
U-Boot-mONStR> md 441bf650
441bf650: 3c343e46 6f756e64 20464454 20617420 <4>Found FDT at
441bf660: 30783435 31303030 30300a3c 353e4c69 0x45100000.<5>Li
441bf670: 6e757820 76657273 696f6e20 322e362e nux version 2.6.
441bf680: 32302d75 63302028 6d696372 6f626c61 20-uc0 (microbla
441bf690: 7a65406d 6f6e7374 722e6575 29202867
ze@xxxxxxxxx) (g
441bf6a0: 63632076 65727369 6f6e2033 2e342e31 cc
version 3.4.1
441bf6b0: 20282050 6574614c 696e7578 20302e32 ( PetaLinux 0.2
441bf6c0: 30204275 696c6420 2d726331 20303530 0 Build -rc1 050
441bf6d0: 36303720 29292023 31382046 7269204e 607 )) #18 Fri N
441bf6e0: 6f762032 33203136 3a34303a 35302043 ov 23 16:40:50 C
441bf6f0: 45542032 3030370a 3c363e73 65747570 ET 2007.<6>setup
441bf700: 5f637075 696e666f 3a20696e 69746961 _cpuinfo: initia
441bf710: 6c697369 6e670a3c 363e7365 7475705f lising.<6>setup_
441bf720: 63707569 6e666f3a 20557369 6e672066 cpuinfo: Using f
441bf730: 756c6c20 43505520 50565220 73757070 ull CPU PVR supp
441bf740: 6f72740a 3c333e20 2d3e2065 61726c79 ort.<3> -> early
If you see linux kernel log - you win. Your serial driver is not
configured properly.
Regards,
Michal
Simek
www.monstr.eu___________________________
microblaze-uclinux mailing list
microblaze-uclinux@xxxxxxxxxxxxxxProject Home Page :
http://www.itee.uq.edu.au/~jwilliams/mblaze-uclinuxMailing List Archive :
http://www.itee.uq.edu.au/~listarch/microblaze-uclinux/