[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [microblaze-uclinux] Spartan-3e: Use DCE instead of DTE
- To: microblaze-uclinux@xxxxxxxxxxxxxx
- Subject: Re: [microblaze-uclinux] Spartan-3e: Use DCE instead of DTE
- From: "Tommy Kamps" <tommy.kamps@xxxxxxxxx>
- Date: Tue, 20 May 2008 09:29:09 +0200
- Dkim-signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=gmail.com; s=gamma; h=domainkey-signature:received:received:message-id:date:from:to:subject:in-reply-to:mime-version:content-type:content-transfer-encoding:content-disposition:references; bh=svXkrXckpF4ASEytKZquwrQFTiEXBL0tdVHsVVSgcLo=; b=Hhg8QVtRd+nKQDnt4tG3HZfcj7nasBQz6ftfkce7yx89E6Wx3ocK7FYQ7fSkEa1oYxMg+yVVcAW88oKsYRyLT23eP3DIoipZI5PdGAuH8hIjWAFgXmtMCob3o6GwBeGy7XK1vklIUvWLhuyXuKMDWdPc1nMBz0ZvGFdx0a2J3AU=
- Domainkey-signature: a=rsa-sha1; c=nofws; d=gmail.com; s=gamma; h=message-id:date:from:to:subject:in-reply-to:mime-version:content-type:content-transfer-encoding:content-disposition:references; b=Zi868lhvVOl4hbvepowFuHlC4jHh3i4d3EaAVmNp2oegkJl6J6NXSh8dD1+i2hZJ331eXkzUOR+ujeQleVQPiXof8wB662HBIoQoZYojO9Wl1GU5B7nkw4SxPw5KUr4Lzz0qtny2qQc9wL2t9k2kxcjLLrRi9d7eK9RzPqjBv6A=
- In-reply-to: <7e4129e40805191014p5565d7fek88ac90d108eb8726@xxxxxxxxxxxxxx>
- References: <7e4129e40805191014p5565d7fek88ac90d108eb8726@xxxxxxxxxxxxxx>
- Reply-to: microblaze-uclinux@xxxxxxxxxxxxxx
- Sender: owner-microblaze-uclinux@xxxxxxxxxxxxxx
Hi Chris,
If you are using the wizard from EDK you are given the choice in the
board hardware setup: you can choose either one or both of the serial
controller peripherals in your hardware design.
If you do not want to use the wizard (again), the solution is also
very easy. Just change the pin locations of the tx and rx pins; the
rest of the configuration can remain the same. I cannot give you the
exact locations, because it is not entirely clear which board you are
using, but this can be found in the board's documentation.
Tommy Kamps
On Mon, May 19, 2008 at 7:14 PM, Chis Dan <dan.ionut.chis@xxxxxxxxx> wrote:
> Hi everyone,
>
> I doing a project for school which involves running uClinux on a Spartan-3e
> board. The problem I'm having is that I only have a cable connecter for the
> DCE port and not for the DTE. So how should I proceed in changing DTE to DCE
> in the hardware design ? Could you help me please or point me to the right
> place on the mailing list where this problem has already been discussed.
>
> Thx,
> DAN
>
___________________________
microblaze-uclinux mailing list
microblaze-uclinux@xxxxxxxxxxxxxx
Project Home Page : http://www.itee.uq.edu.au/~jwilliams/mblaze-uclinux
Mailing List Archive : http://www.itee.uq.edu.au/~listarch/microblaze-uclinux/