Re: [microblaze-uclinux] Re: mONStR Uboot - Problems when I try to creat

2008/10/20 Michal Simek <monstr@xxxxxxxxx>

Thanks. I added there some comments about.

> Hi, thank you Michal. It work's correctly.. But the explanation could me
> more explicit for other people.. For example, the part where we inclued
> the lines in the makefile it's important to copy the tabs because
> withouth the tabs when we run make the makefile shows errors.

I fixed it. There are a lot of examples.

> Also when you say that we have to
> copy include/configs/ml401.h to mb_first.h
>
> where exctly goes mb_first.h ?, It's seems that mb_frist.h has to be
> copied in mb_boot root directory but when I checkout include/config.h
> I rename this file in the same directory.

no - include/configs/mb_first.h is the correct location. If you want to have
mb_first.h in root, you will have to create sym link from
include/configs/mb_first.h to your root path. (do not forget to use relative path)

> Otherwise, the make runs correctly.
>
> Thank you for help me Michal

Thanks,
Michal

>
> 2008/10/17 Michal Simek <monstr@xxxxxxxxx <mailto:monstr@xxxxxxxxx>>

>
> Hi Juan Pablo,
>
> there were small fault. Sorry for that. I wrote it from my mind.
> I added some logs too. :-)
> I have tested and work.
>
> go to board/mb_first and rename ml401.c to mb_first.c (the name must
> be the same
> as is name of board)
>
> libmb_first is here
>
> [monstr@xxxxxxxxx u-boot-denx-de]$ cd board/mb_first/
> [monstr@xxxxxxxxx mb_first]$ ls

> config.mk <http://config.mk> libmb_first.a Makefile mb_first.c

> mb_first.o u-boot.lds
> xparameters.h
>
> Could you tested again?
>
> Thanks,
> Michal
>
>
> Juan Pablo Gómez wrote:
> > Greetings Michal I'm following the guide for use U-Boot
> > (http://monstr.eu/wiki/doku.php?id=uboot:uboot)
> >
> > But when I try to create my own board I've this problem :
> >
> > make[1]: *** The no rule for build the objetive `mb_first.o',
> necesary
> > for `libmb_first.a'. Stop
> >
> > Perhaps there's any mistake on the section, after build de U-Boot I
> > followed these steps for use a xupv2p board :
> >
> > 1) copy this directory : board/xilinx/xupv2p with this new name
> > board/mb_first
> >
> > 2) copy this file include/configs/xupv2p.h with this name to
> > include/configs/mb_first.h
> >
> > 3) change mb_first.h, the include file (#include
> > "../board/xilinx/ml401/xparameters.h") to #include
> > "../../board/mb_first/xparameters.h"
> > The path in the wiki is correct
> "../board/mb_first/xparameters.h" ?
> >
> > 4) I edit the top level Makefile adding these lines
> >
> >
> > mb_first_config: unconfig
> > @mkdir -p $(obj)include
> > @echo "#define CONFIG_MB_FIRST 1" > $(obj)include/config.h
> >
> > @$(MKCONFIG) -a $(@:_config=) microblaze microblaze mb_first
> >
> >
> > It's seems that thw word FIRST was writed incorrectly, and don't
> forget
> > the tab's.
> >
> > I followed these steps but the result was unsuccessful, waht I
> should do?
> >
> > Thank you Michal and regards, Juan Pablo
> >
> >
> >
>
>
>
>
> --
> Muchas gracias.
>
> Atentamente, Juan Pablo Gómez

___________________________
microblaze-uclinux mailing list

microblaze-uclinux@xxxxxxxxxxxxxx

Project Home Page : http://www.itee.uq.edu.au/~jwilliams/mblaze-uclinux
Mailing List Archive : http://www.itee.uq.edu.au/~listarch/microblaze-uclinux/

Re: [microblaze-uclinux] Re: mONStR Uboot - Problems when I try to create my own board