Hi Juan Pablo,
yes, I should use top bsp instead of petalinux and u-boot one. Top bsp which I
made called all bsp which you need. Just set it and rebuild libs.
Top bsp has restricted license about sharing but you can using without any
problems.
Michal
> 2008/10/20 Michal Simek <monstr@xxxxxxxxx <mailto:monstr@xxxxxxxxx>>
> Hi Michal, thank you for the answers.
>
> When I try to make the bistream for use FS-BOOT with U-BOOT these errors
> appears and FS-BOOT didn't compile :
>
> (This is a image : ) http://img377.imageshack.us/img377/5333/fsbootgb1.png
>
> When I build the Libraries and BSP file, the
> microblaze_0\include\auto-config.h (At the root of the project) file is
> not generate and this file is necesary for the compilation of FS-BOOT.
> Should I still use FS-BOOT?? What I've to do for compile FS-BOOT with
> the mONStR Uboot.
>
> Again thanks for your help.
>
>
>
>
>
>
>> <mailto:monstr@xxxxxxxxx> <mailto:monstr@xxxxxxxxx
> Thanks. I added there some comments about.
>
> > Hi, thank you Michal. It work's correctly.. But the explanation
> could me
> > more explicit for other people.. For example, the part where we
> inclued
> > the lines in the makefile it's important to copy the tabs because
> > withouth the tabs when we run make the makefile shows errors.
>
> I fixed it. There are a lot of examples.
>
> > Also when you say that we have to
> > copy include/configs/ml401.h to mb_first.h
> >
> > where exctly goes mb_first.h ?, It's seems that mb_frist.h has to be
> > copied in mb_boot root directory but when I checkout include/config.h
> > I rename this file in the same directory.
>
> no - include/configs/mb_first.h is the correct location. If you want
> to have
> mb_first.h in root, you will have to create sym link from
> include/configs/mb_first.h to your root path. (do not forget to use
> relative path)
>
>
> > Otherwise, the make runs correctly.
> >
> > Thank you for help me Michal
>
> Thanks,
> Michal
>
> >
> > 2008/10/17 Michal Simek <monstr@xxxxxxxxx
> <mailto:monstr@xxxxxxxxx>>>> > config.mk <http://config.mk> <http://config.mk> libmb_first.a
> >
> > Hi Juan Pablo,
> >
> > there were small fault. Sorry for that. I wrote it from my mind.
> > I added some logs too. :-)
> > I have tested and work.
> >
> > go to board/mb_first and rename ml401.c to mb_first.c (the
> name must
> > be the same
> > as is name of board)
> >
> > libmb_first is here
> >
> > [monstr@xxxxxxxxx u-boot-denx-de]$ cd board/mb_first/
> > [monstr@xxxxxxxxx mb_first]$ ls
> <mailto:microblaze-uclinux@xxxxxxxxxxxxxx>> Makefile mb_first.c
> > mb_first.o u-boot.lds
> > xparameters.h
> >
> > Could you tested again?
> >
> > Thanks,
> > Michal
> >
> >
> > Juan Pablo Gómez wrote:
> > > Greetings Michal I'm following the guide for use U-Boot
> > > (http://monstr.eu/wiki/doku.php?id=uboot:uboot)
> > >
> > > But when I try to create my own board I've this problem :
> > >
> > > make[1]: *** The no rule for build the objetive `mb_first.o',
> > necesary
> > > for `libmb_first.a'. Stop
> > >
> > > Perhaps there's any mistake on the section, after build de
> U-Boot I
> > > followed these steps for use a xupv2p board :
> > >
> > > 1) copy this directory : board/xilinx/xupv2p with this new
> name
> > > board/mb_first
> > >
> > > 2) copy this file include/configs/xupv2p.h with this name to
> > > include/configs/mb_first.h
> > >
> > > 3) change mb_first.h, the include file (#include
> > > "../board/xilinx/ml401/xparameters.h") to #include
> > > "../../board/mb_first/xparameters.h"
> > > The path in the wiki is correct
> > "../board/mb_first/xparameters.h" ?
> > >
> > > 4) I edit the top level Makefile adding these lines
> > >
> > >
> > > mb_first_config: unconfig
> > > @mkdir -p $(obj)include
> > > @echo "#define CONFIG_MB_FIRST 1" > $(obj)include/config.h
> > >
> > > @$(MKCONFIG) -a $(@:_config=) microblaze microblaze
> mb_first
> > >
> > >
> > > It's seems that thw word FIRST was writed incorrectly, and don't
> > forget
> > > the tab's.
> > >
> > > I followed these steps but the result was unsuccessful, waht I
> > should do?
> > >
> > > Thank you Michal and regards, Juan Pablo
> > >
> > >
> > >
> >
> >
> >
> >
> > --
> > Muchas gracias.
> >
> > Atentamente, Juan Pablo Gómez
> ___________________________
> microblaze-uclinux mailing list
> microblaze-uclinux@xxxxxxxxxxxxxx
> <http://www.itee.uq.edu.au/%7Ejwilliams/mblaze-uclinux>
> <http://www.itee.uq.edu.au/%7Elistarch/microblaze-uclinux/>
>
>
>
>
> --
> Muchas gracias.
>
> Atentamente, Juan Pablo Gómez
___________________________
microblaze-uclinux mailing list
microblaze-uclinux@xxxxxxxxxxxxxx
Project Home Page : http://www.itee.uq.edu.au/~jwilliams/mblaze-uclinux
Mailing List Archive : http://www.itee.uq.edu.au/~listarch/microblaze-uclinux/